Why should you back toward the driver's side? Back to the driver's side so you can see better. Backing toward the right side is very dangerous because you can't see as well. If you back and turn toward the driver's side, you can watch the rear of your vehicle by looking out the side window.
Also to know is, what are two special conditions where you should downshift?
slow down and shift to a speed that you can control without using the brakes hard. Otherwise the brakes can overheat and lose their braking power.
Subsequently, question is, what are the advantages of going right instead of left around an obstacle? If an oncoming driver has drifted into your lane, a move to your right is best. If that driver realizes what has happened, the natural response will be to return to his or her own lane. If the shoulder is clear, going right may be best.
Also know, what is the most important reason for doing Vehicle Inspection?
Safety is the most important reason you inspect your vehicle, safety for yourself and other road users.
What are two main things to look ahead for?
Look for traffic: Vehicles coming onto the highway, into our lane, or turning. Watch for break lights from slowing vehicles. Look for road conditions.
How can you start moving without rolling backward?
If stopped on a hill, how can you start moving without rolling back? partly engage the clutch before you take your right foot off the brake. Release the parking brake with enough engine power. the hand valve can be applied to keep from rolling back.What are 2 ways to know when to shift?
There are two ways of knowing when to shift: Use Engine Speed (rpm). Study the driver's manual for your vehicle and learn the operating rpm range. Watch your tachometer, and shift up when your engine reaches the top of the range.Why is it important to shift gears correctly?
Shift Gears Properly. It's important to be in the correct gear. This tip is more aimed at drivers of cars with manual transmissions. While it's effective in slowing down the car, and can make going around corners easier, engine braking can produce excessive wear on your engine.Is it bad to downshift in an automatic?
Never use the automatic transmission to slow down This practice is not acceptable in automatic transmissions because a forced downshift at high-engine RPMs can result in excessive transmission wear, specifically to the clutch friction plates and the transmission bands.How many seconds of following distance should you allow?
The two-second rule is a rule of thumb by which a driver may maintain a safe trailing distance at any speed. The rule is that a driver should ideally stay at least two seconds behind any vehicle that is directly in front of his or her vehicle.How should you know when to shift CDL?
Knowing When to Shift Up Study the driverʼs manual for your vehicle and learn the operating RPM range. Watch your tachometer, and shift up when your engine reaches the top of the range. (Some newer vehicles use “progressive” shifting: the RPM at which you shift becomes higher as you move up in the gears.What is the most important hand signal that you and your helper should agree on?
The most important hand signal to discuss and agree upon is the one used for "stop.” It is important that the helper stand at the back of the vehicle, in a spot where the driver can see them clearly. This will help collisions and aid the driver during "blind spots."Where should your reflectors be placed on a divided highway?
Place your warningdevices at the following locations: On the traffic side of the vehicle, within ten feet of the front or rear corners — to mark the location of the vehicle. 100 feet behind and ahead of the vehicle, on the shoulder or in the lane you are stopped in.When should stab braking never be used?
Stab braking is used on cars without ABS brakes and it consists of these steps: Applying the brakes all the way. Releasing the brakes when the wheels lock up. As soon as the wheels start rolling, put on the brakes fully again.When you do a walk around inspection you should?
Name some things you should check on the front of your vehicle during the walk-around inspection.- Go to front of vehicle and check that low beams are on and both of the 4-way flashers are working.
- Push dimmer switch and check that high beams work.
- Turn off headlights and 4-way, hazard warning flashers.
What are the three types of emergency equipment?
What three kinds of emergency equipment must you have? Spare electrical fuses, three red reflective triangles, properly charged and rated fire extinguisher.How many red reflectors should you carry?
Preview Flashcards| Front | Back |
|---|---|
| How many red reflective triangles should you carry? | 3 |
| How do you test hydraulic brakes for leaks? | Pump the brake pedal three times, apply firm pressure, hold for five seconds. The pedal should not move. |
| Why put the starter switch key in your pocket during the pre-trip inspection? | For your safety |
What effects can wet brakes cause?
When driving in heavy rain or deep standing water, your brakes will get wet. Water in the brakes can cause the brakes to be weak, to apply unevenly, or to grab. This can cause lack of braking power, wheel lockups, pulling to one side or the other, and jackknife if you pull a trailer.What is the best way to see the sides and rear of your vehicle?
Continuing Education Commercial Driving- Regularly looking out the window and checking behind you.
- Checking your mirrors regularly and more often in special situations.
- Installing a rear camera system is the safest way to see sides of your vehicle.
- Using a passenger to look out the windows and check the mirrors for you.
Which of the following are possible causes of tire fires?
Following are some causes of vehicle fires: After accidents - Spilled fuel, improper use of flares. Tires - Underinflated tires and duals that touch. Electrical system - Short circuits due to damaged insulation, loose connections.What is the first step of proper braking technique when going down a steep downgrade?
Describe the proper braking technique when going down a long, steep downgrade.- Apply the brakes just hard enough to feel a definite slowdown.
- When speed has been reduced to approximately five mph below your "safe" speed, release the brakes.
- Repeat when speed has increased to your "safe" speed.
