The Good News
| Male Thread Size | AN Size* | Equivalent Tube Size (Nominal OD) |
|---|---|---|
| 7/16-20 | 4AN | 1/4" |
| 9/16-18 | 6AN | 3/8" |
| 3/4-16 | 8AN | 1/2" |
| 7/8-14 | 10AN | 5/8" |
Then, what size are fuel lines?
Most stock applications came with 5/16-inch fuel line, but for many street vehicles and mild race applications 3/8-inch (AN 6) fuel line is a good upgrade. High performance applications and racers using alcohol will use 1/2-inch (AN 8) fuel line.
Likewise, is 6an the same as 3 8? No they aren't exactly the same. Most people compare them because they are close and flow roughly the same. According to this, AN and hard line are OD measurements and NPT is inside diameter so for AN and hard line the inside diameter would depend on the thickness of the tubing.
Considering this, is 6an bigger than 8an?
036 and smaller) the -6AN feedline flowed more than the -8AN line did, but with jet sizes larger than . 040 the larger -8AN hose proved beneficial.
How much HP will 6an fuel line support?
A #6 AN line can easily support 2000 HP as long as you have enough pump head !!!" You will want -8 for the volume and heat.
What size should my fuel return line be?
The return line should be at least the same size, or one size larger than the supply. Make sure there are no sharp bends or kinks. The return line should direct fuel close to the bottom of the tank and away from the pickup.What size is 8an fuel line?
The Good News| Male Thread Size | AN Size* | Equivalent Tube Size (Nominal OD) |
|---|---|---|
| 3/8-24 | 3AN | 3/16" |
| 7/16-20 | 4AN | 1/4" |
| 9/16-18 | 6AN | 3/8" |
| 3/4-16 | 8AN | 1/2" |
Is fuel line measured ID or OD?
Tubing is OD (outside diameter) and Pipe is ID (inside diameter). So the easiest way to tell the size of your fuel line, which is tubing, is to use a combination wrench. Whichever one slips over snuggly is the winner.Is hose measured by ID or OD?
Simply put, a dash size refers to a I.D. of a hydraulic hose or fitting in 1/16" increments. For example, -6 hose would indicate a hose with I.D. of 6/16" - or 3/8". Hoses are measured by inside diameter, unlike tubes which are measured by outside diameter.How much horsepower will a 3/8 fuel line support?
A 3/8”id fuel line can easily support 600 HP given sufficient “pump head”! Given a big enough pump a 3/8” steel line could support 1000 HP. The simple way to know is to install an electronic fuel pressure gage. If the pressure falls as the engine RPM's go up you need more pump head.How do you seal fuel line fittings?
To choose the appropriate thread sealant, look for it's chemical resistance to fuel (diesel or gasoline) or oil running through the line. Backyard mechanics will tell you they've used regular old gas resistant teflon tape (yellow stuff) with success. This is not recommended because it risks breaking free.How much pressure does a fuel line have?
Working pressure is not relevant, but wire-inserted hose can withstand 50-85 psi, depending on diameter. High-pressure fuel hose for clamp-type fuel-injection systems is also available. This fuel hose is SAE 30R9-rated and uses a fluoro elastomer inner liner that will withstand up to 180 psi and 300 degrees.What size is an fitting?
Each AN size refers to the outer diameter (o.d.) of the tube, or inner diameter (i.d.) of the hose that it's used with. The numbers assigned equal the size in 1/16 inch increments. Each AN size also has its own standard thread size.How is fitting size measured?
Measure the Outside Diameter (OD) of your pipe or pipe fitting: Wrap a string around the pipe. Mark the point where the string touches together. Use a ruler or measuring tape to find the length between the tip of the string and the mark you made (circumference)What size is 10 an fitting?
Russell Performance Technical Support| AN Size | Metal Tube O.D. | Thread Size |
|---|---|---|
| -8 AN | 1/2" | 3/4" - 16 SAE |
| -10 AN | 5/8" | 7/8" - 14 SAE |
| -12 AN | 3/4" | 1-1/16" - 12 SAE |
| -16 AN | 1" | 1-5/16" - 12 SAE |
What size is #6 JIC fitting?
JIC 37° Flare & Uno (O Ring Boss) Threads| MALE THREAD OD & PITCH | DASH SIZE | FEMALE THREAD ID |
|---|---|---|
| inch – TPI | mm | |
| 5/16 – 24 UNF | -05 | 6,9 |
| 3/8 – 24 UNF | -06 | 8,5 |
| 7/16 – 20 UNF | -07 | 9,9 |
