Blue Flame gas log lighters simplify the process of lighting your wood burning fireplace. Blue Flame log lighters will also help prevent build up of creosote caused by lack of proper draft at the early stage of lighting your wood burning fireplace.Similarly one may ask, how do you use a blue flame log lighter?
Locate log lighter as indicated above and maintain proper clearances. 4. The log lighter should be located such that the burner ports are facing inwards at 30-45 degrees, with the air shutter facing out towards the front. Adjust the air shutter to give sharp blue flames with yellow tips.
Beside above, what does a blue flame mean when burning wood? A Blue Flame Indicates Complete Burning of Carbon Propane gas, like firewood, contains carbon compounds. However, it often produces a blue flame instead of an orange or yellow flame because it burns all the carbon.
Simply so, what is a log lighter valve?
Valve Kits– Log Lighter. A fully complete valve, key, log lighter and fittings to install a log lighter in an indoor fireplace. These components are specifically designed to hold up to the heat a wood burning fireplace produces.
Why is the flame blue in my gas fireplace?
A blue flame indicates that the burner is providing an air-fuel mix with sufficient oxygen for complete combustion right out of the nozzle. The flame burns the fuel completely to carbon dioxide and water. The other set of burners were adjusted to produce a yellow flame, designed to look like a wood fire.
How do you use a log lighter?
Turn log lighter gas valve to the “off” position. Place logs on the fireplace grate allowing sufficient air space between logs for quick lighting. Light a long-stemmed fireplace match and hold it toward the center of the cast-iron burner ports. Turn the log lighter valve “on” gradually until ignition occurs.How do you install a log lighter?
Start by turning off the gas to your home. Make sure your firebox is completely free of any debris. Connect the log lighter starter pipe to the 1/2" male nipple and slide the nipple from the inside of the fireplace through the hole you drilled. (All other work will be done outside the fireplace).How many BTU is a log lighter?
Are Log Lighters Required to be listed or Approved? What About Propane? A one half inch gas line is typical and seems to be adequate for any of our Rumford gas log sets which put out from about 90,000 BTUs for the smaller sets to about 200,000 BTUs for the larger sets.What is a gas log lighter?
Fireplace log lighters can be your trusted gas fireplace starters. With a connection to a professionally installed fuel line (either natural gas or propane) and the turn of a valve key, gas is delivered into the pipe.What is a gas starter fireplace?
Gas starters make it easy to start a fire in a wood-burning fireplace. Consisting of a tube mounted under the grate, a gas starter uses natural gas to create flames through several small holes along its length. These flames light the wood; once the wood is well-lit, you can turn off the gas starter.What is a zero clearance fireplace?
Zero-Clearance Fireplaces are pre-manufactured fireplaces where the unit or firebox can be placed almost directly against combustible materials like wood, walls, or paneling. Often much more than a traditional open fireplace which means less heat and energy is wasted up and out the chimney.How do you light a wood burning gas fireplace?
Turn the knob from the “Off” to the “Pilot” position. Push in the pilot knob, which manually sends gas into the system. Push the igniter button once every second until it lights. Depending on how long it's been since the gas fireplace was last used, ignition may take multiple attempts.How do you light a gas fireplace?
Hold the gas control button down while you hold the end of a lighted match or lighter at the end of the pilot tube. If you do this correctly, the pilot light should start as soon as the flame is close enough. Hold the pilot button down for about 20 seconds to give the thermocouple time to heat up, then release it.What Colour flame is dangerous?
Yellow or red flames only burn at around 1,000 degrees C. This flame is dangerous as it produces more poisonous carbon monoxide gas.What gives off a blue flame?
Several metal salts burn with a blue flame, such as certain copper, arsenic, and lead compounds. Antimony and lead are toxic, but you can use copper(I) chloride to produce blue fire by following these instructions: Add a small amount of water to copper(I) chloride to dissolve the salt.What does a blue flame mean spiritually?
The Blue Flame is in the core of the very strength and energy. The basic qualities of the Blue Flame are manifested through the energies of power, strength, faith and protection. The Blue Flame Invocations should be performed on Sunday, since this is the day when the irradiation of this Ray is especially dominant.What is the hottest fire color?
The hottest flame is violet on the color spectrum and white in the visible spectrum. The type of fuel and impurities, in addition to the flame temperature, contribute to the color of the flame. Once the gas forms, combustion occurs as the various molecules react with oxygen to produce the heat and light known as fire.What Colour flame is carbon monoxide?
Gas flames burning orange or yellow instead of blue may indicate the presence of carbon monoxide.Are Black Flames possible?
Flames emits light and heat, so it seems impossible to make black fire. However, you actually can make black fire by controlling the wavelengths of absorbed and emitted light.What are the colors of fire?
Colored fire is a common pyrotechnic effect used in stage productions, fireworks and by fire performers the world over. Generally, the color of a flame may be red, orange, blue, yellow, or white, and is dominated by blackbody radiation from soot and steam.What does a purple flame mean?
Keep in mind "purple" is a tricky fire color to produce because there is no wavelength of light that is responsible for a color between red and violet, yet fire colors mostly are produced by the emission spectra of chemicals. In order to get purple, you need to produce violet flame and red flame.What color does nitrogen burn?
Dicyanoacetylene, a compound of carbon and nitrogen with chemical formula C4N2 burns in oxygen with a bright blue-white flame at a temperature of 5,260 K (4,990 °C; 9,010 °F), and at up to 6,000 K (5,730 °C; 10,340 °F) in ozone. 
