about 2.5"
Furthermore, what size does drip edge come in?
This profile of drip edge is shaped like a “T,” with a lower flange at the bottom. Roof drip edges are generally sold in 10.5-foot lengths, but they are occasionally sold in 8-foot lengths or smaller. The length of the overhang itself commonly ranges from 2 to 5 inches.
Similarly, should shingles hang over drip edge? The edge of the shingles should hang over a roof between an inch and an inch and a half — or between a half inch and three-quarters of an inch if drip edge flashing is installed. Too much overhang and the shingles could blow off in high winds; too little can allow water to seep into rake or fascia boards.
Keeping this in consideration, how do you measure drip edge?
Measure for drip edge. This metal strip, which goes beneath the underlayment, protects the edge of the roof from rot. You'll need the measurements of the rakes and eaves of the roof (side edges and bottom edge). Use a rake edge for the side of the house as well.
Is drip edge the same as flashing?
So as rain drips off the shingle, the drip edge keeps the wind from blowing the water back behind the gutter or back up under the shingles. Flashing is the general term for metal used where roofing meets a wall or a roof edge to keep rain from getting under shingles.
Does drip edge go under tar paper?
The drip edge should be over the paper at the eaves, and under along the rake. mroberson: Its a TRAP! Back in my construction days, I learned that you place the tar paper OVER the drip edge on the eaves so if moisture gets through the shingles, it does not get under the drip edge.Do you install gutters under drip edge?
If your gutter has been previously installed, rather than taking it down and redoing it, you can easily place a small strip of metal flashing under the drip edge and over the back of the gutter (as shown by the illustration at the bottom of this page) so the water will shed into the gutter.Should drip edge be tight to fascia?
The drip edge should be installed over a piece of 1×2 furring strip so that it stands off from the fascia or rafter tails. If the drip edge is laid right up against the fascia or rafters, then because of surface tension, the water runs right up against the fascia and underneath the soffit.Where is drip edge installed?
Install roof drip edge along the eaves, add underlayment, then place drip edge along the gable end. The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge.Do you need a drip edge with metal roofing?
A drip edge is a metal (usually aluminum) strip which extends beyond other parts of a roof and directs rainwater off the roof away from the fascia and into the gutter. This is important because a badly positioned drip edge—or no drip edge at all– can cause overflowing of gutters, over front or back.How much does a drip edge cost?
Drip Edges: $1-$2 per linear foot installed. Inspect and replace drip edges as necessary. Drip edges are added to the roof to direct water into the gutters. Other Damage – Have a professional inspect your eaves for damage before repairing fascia and soffits.What is the difference between drip edge and rake edge?
Drip edge and rake edge are the first parts of the roof system to be installed. Drip edge goes along your eaves trough areas and rake edge goes along your gable ends. They both look very similar and are often not differentiated in name by some suppliers and simply called drip edge.Do you nail drip edge?
Nail the drip edge to the roof deck with minimum 12-gage roofing nails spaced 8 to 10-inches on center and 1-½ to 3-inches from the edge of the sheathing. Adjacent drip edge pieces should be lapped minimum 2 inches. Asphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch.Can you install drip edge on existing roof?
Replacing Drip Edge Eave Strips: Install the eave strips on the lower roof edges first, with the eave strips under the shingles and felt underlayment. Align one end of the lower eave strip even with the edge of the roof decking. Lift up roof shingles, and nail the eave strip in place with galvanized roofing nails.What color drip edge should I use?
The most common colors for drip edge are white and brown. However, some roofing companies can provide color match drip edge. The color is often chosen to match the shingles or the gutters to create a seamless look. The color can also be chosen to match the shutters or trim of the house and act as an accent color.How many bundles of shingles do I need for 2000 square feet?
How Many Shingles Do I Need to Cover a Roof? The number of bundles or squares you need will depend on the surface area of your roof, and its pitch or slope. For example, a 2,000-square foot roof will require 20 squares or 60 bundles.Why do my gutters drip?
If the gutters are clogged, it's possible that the water is overflowing the gutters and this is contributing to the leak. Water should run out the downspout and away from the house without filling the gutter. If the water fills the inside of the gutter, this means the gutters are clogged.How many bundles of shingles do I need for 1200 square feet?
The average bundle of shingles covers 33.3 ft2, so three bundles of shingles are needed per square.How far should Roof sheathing overhang fascia?
It is at 45-3/4 in. Measure up the rafter 45-3/4 inch from the cut end of the truss tail and snap a line along the trusses. This indicates the upper edge of the first row of roof sheathing—leaving enough overhang that the subfascia and fascia will tuck neatly underneath when the time comes.How do you install drip edge after shingles?
Make sure the outer edge extends over the gutter. If it doesn't, pull the drip edge out slightly from under the shingles. Secure the drip edge with roofing cement. Apply a continuous bead of cement along the top of the drip edge, then press down on the shingle.What is a house Gable?
A gable is the generally triangular portion of a wall between the edges of intersecting roof pitches. The shape of the gable and how it is detailed depends on the structural system used, which reflects climate, material availability, and aesthetic concerns.Does roofing felt go under flashing?
1 Answer. It depends on where the drip edge is. At the side, or gabels, of a roof, the drip edge goes over the roofing felt. At the bottom of the roof, the drip edge goes under the roofing felt. 
