How do you use a SpeeCo wire gripper?

To use this tool, slide the ring towards the eye, and find the groove in the ring. Put the wire through the groove, and rotate the ring, so that the groove is on the opposite side of the wire.

Keeping this in consideration, how do you use a come along to tighten a fence?

Place the knobbed side of the T-post on the inside of the fence. Unroll the barbed wire along the line of the fence posts. Fasten the wire to one of the corner posts and pull it as tightly as possible to the next corner post. Use a wire stretcher, a mechanical ratchet device, to pull the wire tighter.

Subsequently, question is, how tight should barbed wire be? High tensile barbed wire can be installed up to 30' with stays. Low carbon wire can be installed at 12-15'. For high tensile barbed wire, pull the wire until it is tight, but not too tight. Over-tightening will cause stress and breakage.

Likewise, people ask, can you put barbed wire on your fence?

Police advice on boundary security states: 'Do not use barbed wire, razor wire or broken glass on walls or fences to protect your property – you could be held legally responsible for any injuries caused. '

Can barbed wire kill you?

Barbed wire has been a serious issue for quite a long time now, so whenever you can, avoid it, because it can and will kill you.

Why is it called concertina wire?

It is called concertina wire, named after the musical instrument and its expanding and contracting bellows. It resembles barbed wire that's commonly used to corral cattle, but it comes in flat coils that can quickly expand like its namesake, making it easier to store, transport and install.

Do you stretch welded wire fence?

Welded wire fencing material cannot be tightened as much as woven wire meshes, such as field fence, horse fence, deer and wildlife fence. Don't forget to bring along a helper like Little Bit!

How do you tighten a chicken wire fence?

Manual Tensioning With Help

1. STEP 1) Attach a Broom Handle. Thread a piece of wood such as a broom handle through the chicken wire holes so that it allows your helper to grip and pull the chicken wire tight.
2. STEP 2) Pull the Broom Handle & Staple the Chicken Wire to the Post.
3. STEP 3) Rinse & Repeat.

How do you tighten a chain link fence?

Thread a tension wire through the bottom loops of the mesh and tighten it around the end posts.

1. Chain link mesh must be pulled taut or it will sag. Stretching is done with a tool called a fence puller.
2. Insert a pull bar through the unattached mesh a few feet from the final post.
3. Attach the yoke to the pull bar.

How do you make a wire fence?

welded wire fencing

1. Step 1: INSTALL THE POSTS AND CUT TOP RAILS.
2. Step 2: STAPLE MESH TO POST AND TOP RAIL.
3. Step 3: STAPLE MESH TO POST AND BOTTOM RAIL.
4. Step 4: TRIM EXCESS MESH.
5. Step 5: SPLICE IN A NEW ROLL IF NECESSARY.
6. Step 6: ADD A CAP RAIL.
7. Step 7: FOR FASTER INSTALLATION, USE METAL POSTS.

What is a post puller?

Definition of post puller. An electric vehicle having a powered drum for handling wire rope used to pull mine props after coal has been removed; used for the recovery of the timber.

How do you install an uneven ground fence?

Nail the measured rails to the middle of the premeasured fence posts. Review the straightness of the line before you remove the stakes for post-holes. Dig the pits with a mattock and set the fence posts. Attach the top and bottom rails and follow the contour of the land.

What is a fence stretcher?

Fence stretchers are used to provide the proper amount of tension on wire fences. A tight fence protects livestock and wildlife from getting tangled in the fence which could cause injury or even death. They all work the same with some type of clamp to attach to the wire and a ratcheting system to tighten it.